How to get an accurate result from the Roofing Calculator
An accurate roofing result comes from three habits: measure the two inputs properly, let the Roofing Calculator do the maths, and add waste yourself afterwards, because the tool does not add it. Most accuracy problems come from what is typed in, not from the tool, so this guide spends most of its time on the measuring.
At a glance
Measure the footprint to the nearest 10 cm
Measure the outside length and width at ground level, and round each to the nearest 10 cm before you multiply. A house measured as 12.0 m by 10.0 m has a footprint of 120 m². A 10 cm error on each side changes the footprint by about 2.2 m², which is only 0.27 squares at 30° — small, but worth avoiding when the tape is already in your hand.
Measure the pitch in degrees, not by eye
A pitch guessed by eye is often 5° out, and 5° matters. On a 120 m² roof, 25° gives 14.25 squares and 30° gives 14.91 squares — a gap of 0.66 squares, which can tip the order from 15 squares to 16. Use an angle finder, a phone level, or the rise over a measured run, and convert the rise to degrees before you type it in.
Worked example: 120 m² at 30°, with waste
Roof area = 120 ÷ cos(30°) = 120 ÷ 0.8660 = 138.56 m², which is 138.56 × 10.7639 = 1,491.5 sq ft, or 14.91 squares. Rounded up, order 15 squares, which is 45 bundles. For a complex roof, add 10% waste first: 14.91 × 1.10 = 16.40 squares, so order 17 squares, which is 51 bundles. The waste step is yours to do — the tool shows the plain roof only.
Check the answer backwards
Work the answer back to the footprint and see if you land where you began. From 14.91 squares, the roof area is 14.91 × 100 = 1,491 sq ft, or 138.56 m², and 138.56 × cos(30°) = 138.56 × 0.8660 = 120.0 m², the footprint you started with. If the back-check gives a different footprint, a number was typed in wrong.
Match the precision to the job
Two decimal places are enough for the exact squares figure; the order itself is always a whole number. Do not round the pitch to the nearest 10°, and do not round the footprint to the nearest 10 m², because both roundings move the order by a square on a large roof. Keep the inputs precise, and let the round-up happen only at the end.
The common mistake
People add waste by ordering one extra square no matter how big the roof is. On a 24 m² shed that is generous; on a 200 m² house at 30°, where the exact figure is 24.86 squares, one extra square is only 4% waste, not 10%. Work out 10% of your exact squares instead: 24.86 × 1.10 = 27.35, so order 28 squares.
Frequently asked questions
How many squares is 120 m² at 30°?
14.91 squares exactly, so order 15 squares, which is 45 bundles, before waste.
How much waste should I add?
Roughly 10% on a complex roof. For 120 m² at 30° that takes 14.91 squares to 16.40, so order 17 squares, 51 bundles.
How do I check my roofing answer?
Work it backwards: squares × 100 gives square feet, then × cos(pitch) should give back your footprint area.
How precisely should I measure the footprint?
To the nearest 10 cm on each side. A 10 cm error on a 12 m by 10 m house moves the answer by only about 0.27 squares.
More guides on the Roofing Calculator
- How to use the Roofing Calculator — step by step
- Roofing Calculator explained with worked examples
- Roofing Calculator formula — how it actually works
- Roofing Calculator for beginners — start here
- Common mistakes people make with the Roofing Calculator
- Roofing Calculator vs doing it by hand — which is faster?
- roofing calculator — the complete guide
- Roofing Calculator for students — with examples
- Roofing Calculator for homeowners and DIYers
Try the Roofing Calculator — free, in your browser.