← All blog posts

How to use a plant spacing calculator

WhiteUI · A plain-English guide to the Plant Spacing Calculator

The Plant Spacing Calculator takes three numbers — bed length, bed width and plant spacing — and returns how many plants fit, how they are laid out, and what the area method would say. This guide walks through the calculator with its own default values, explains each input and each part of the answer, and shows how to check the result by counting rows. Open the Plant Spacing Calculator and follow along.

The calculator with its defaults, 3 metres by 2 metres at 30 centimetres, shows 60 plants: 10 per row times 6 rows, with an area estimate of 66
The defaults — 3 m by 2 m at 30 cm — give 60 plants: 10 per row × 6 rows, with an area estimate of 66.

The three inputs

Bed length is the long side of the bed, in metres. Bed width is the short side, in metres. Plant spacing is the gap between plants, in metres, measured centre to centre. The calculator's defaults are a bed 3 m long and 2 m wide, with a spacing of 0.3 m, which is 30 cm. All three inputs are in metres, so a spacing from a seed packet in centimetres needs converting first: divide by 100, so 30 cm becomes 0.3, 45 cm becomes 0.45 and 60 cm becomes 0.6. If you enter a spacing of zero or less, the calculator falls back to 0.3 m rather than dividing by zero.

Reading the answer

With the defaults — 3 m by 2 m at 30 cm — the calculator shows 60 plants. That is the headline, and it is the grid count: 10 plants per row × 6 rows. The layout line underneath says exactly that: "10 plants per row × 6 rows", so you can see how the count was reached. Below it, the area estimate reads 66 plants: the bed is 6 m², each plant needs 0.09 m², and 6 ÷ 0.09 = 66. The two numbers differ because the area estimate ignores the edges, while the grid count only counts plants that actually fit. Buy the grid count: 60 plants, not 66.

Try changing one thing at a time

The fastest way to learn the calculator is to change one input and watch the answer. Keep the bed at 2.4 m by 1.2 m and the spacing at 30 cm, and the answer is 32 plants: 8 per row × 4 rows. Now change only the spacing to 60 cm, and the answer drops to 8 plants: 4 per row × 2 rows. The bed did not change, but doubling the spacing quartered the count, from 32 to 8, exactly as the spacing maths says it should. Change the spacing back to 30 cm and lengthen the bed to 3 m, and the answer becomes 40 plants: 10 per row × 4 rows.

Checking the answer by hand

Check the calculator's answer the same way you would check your own: count the rows. Take the 3 m by 1.2 m bed at 30 cm. The width divided by the spacing is 1.2 ÷ 0.3 = 4 rows. The length divided by the spacing is 3 ÷ 0.3 = 10 plants per row. Multiply: 4 × 10 = 40, which matches the calculator. The calculator rounds each division down, so a bed 2.5 m wide at 30 cm spacing gives 8 rows, not 9, and that rounding down is deliberate: a plant with no room is a wasted plant.

plants = floor(length ÷ spacing) × floor(width ÷ spacing)
area estimate = floor(bed area ÷ spacing²)

When to use the calculator, and when not to

Use the calculator when you are planning: trying spacings for a crop, comparing two beds, or working out how much seed to buy. Do not use it as a substitute for measuring the bed. The calculator cannot see the path through your bed, the strip along the fence where nothing grows, or the corner taken up by a water butt, and it will count all of that as planting space. Measure what you will actually plant, enter those numbers, and the answer will be right. And remember that the calculator gives a square grid layout; if you stagger the rows in a triangular pattern, you can fit about 15% more plants than it shows.

Frequently asked questions

How do I use the plant spacing calculator?

Enter bed length, bed width and plant spacing, all in metres. The headline answer is the grid count — plants per row times rows — with an area estimate shown separately.

What do the calculator's default values give?

A 3 m by 2 m bed at 30 cm spacing gives 60 plants: 10 per row × 6 rows, with an area estimate of 66.

Why does the calculator show two different plant counts?

The headline is the grid count, the number you can actually plant. The area estimate ignores edge losses, so it is always the same or higher.

Does the calculator handle triangular spacing?

No, it gives a square grid layout. For staggered rows, add about 15% to its count.

More guides on the Plant Spacing Calculator

Try it yourself

Try the Plant Spacing Calculator — free, in your browser.

Open the Plant Spacing Calculator