← All tools/Tools/Garden & Outdoor/Plant Spacing Calculator

Plant Spacing Calculator

Work out how many plants fit a bed at a given spacing, row by row.

m
m
m

Plants that fit

—

Grid count against the area estimate

Grid layout
Area estimate

How it works

plants per row = floor(length ÷ spacing)
rows = floor(width ÷ spacing)
plants = plants per row × rows
area estimate = floor(length × width ÷ spacing²)

The calculator works on a simple grid. Plants per row is the bed length divided by the spacing, rounded down, because a plant that only half fits at the edge cannot be planted at all. Rows is the same sum with the bed width, and total plants is the two multiplied together. The area estimate divides the whole bed area by the square of the spacing, which counts the leftover strips along the edges as if plants could use them — so it is always equal to or higher than the grid count, and the grid count is the one to order by. Spacing is measured centre to centre, in metres, in both directions. The formula assumes one plant per spot in straight rows; it does not allow for paths inside the bed or for staggered (triangular) planting, which fits about 15% more plants into the same bed.

Worked example: a 3 m by 2 m bed at 0.3 m spacing fits floor(3 ÷ 0.3) = 10 plants per row and floor(2 ÷ 0.3) = 6 rows, so 10 × 6 = 60 plants. The area estimate is floor(6 ÷ 0.09) = 66, which overstates the count because whole plants cannot fill the leftover edges.

Second worked example: a 4 m by 3 m kitchen-garden bed in Chennai, planting tomatoes at 0.45 m spacing. That fits floor(4 ÷ 0.45) = 8 plants per row and floor(3 ÷ 0.45) = 6 rows, so 8 × 6 = 48 plants. The area estimate is floor(12 ÷ 0.2025) = 59, which overstates the count because the 0.4 m strip left along the length and the 0.3 m strip left along the width cannot hold another row.

Frequently asked questions

Why is the grid count lower than the area estimate?

Because plants sit in whole rows. The leftover strip along each edge — 0.2 m in the worked example — cannot hold another row, so the area figure counts space that no plant can use.

Should I buy extra plants?

Buy about 10% extra for losses. Sixty plants plus 10% is 66, which is a sensible order quantity for the worked example.

Does spacing mean centre to centre?

Yes. Spacing is measured from the centre of one plant to the centre of the next, in both directions.

What about paths between rows?

If you need walking paths, widen the spacing or subtract the path area from the bed first. This calculator assumes the whole bed is planted.

Can I use this for pots and containers?

Yes, with one change: use the pot’s diameter as the spacing. A 30 cm pot holds one plant, so a 1.2 m balcony planter fits floor(1.2 ÷ 0.3) = 4 pots in a row. The same centre-to-centre rule applies — leaves need the same room whether the roots are in soil or in a pot — but remember that pots dry out faster, so container plants usually need watering more often than the same plant in a bed.

What the result means

The gap between the grid count and the area estimate is the most useful number on the page: it is the space your plants cannot use. In the worked example the bed loses a 0.2 m strip along each side, which is why the area estimate of 66 is higher than the 60 plants that actually fit. Narrow beds waste the most — a 1 m wide bed at 0.3 m spacing fits 3 rows and wastes the same proportion as a wide one, but the waste is a bigger share of a small bed. Two habits make the number work in practice: buy about 10% extra for seedlings that fail, and leave one spacing-width free at the bed edge for your feet, since a plant hard against the edge is the first to get trodden on. If the gap bothers you, stagger alternate rows — offsetting each row by half a spacing fits roughly 15% more plants — but measure the diagonal spacing too, because staggered plants still need the same centre-to-centre room in every direction.

More tools

Plant Spacing Calculator guides

Tell us what you think

Loving this tool, or stuck on something? Tell us — it takes a minute.

We’ll only use your name and email to reply if needed. The tool and page are filled in for you.