← All blog posts

Common mistakes when calculating plant spacing

WhiteUI · A plain-English guide to the Plant Spacing Calculator

Most spacing mistakes are not gardening mistakes. They are arithmetic mistakes: a unit converted wrong, a method trusted too far, a path forgotten, a measurement taken from the wrong edge. Each one costs plants, either bought and wasted or never planted at all. This guide covers the five mistakes that turn up most often, with the numbers for each, so you can spot them before you buy seed. Check any figure here on the Plant Spacing Calculator.

The area method says 16 plants fit a 4 metre by 1.5 metre bed at 60 centimetre spacing, but counting rows says 12
The area method says 16 plants; counting rows says 12. Buy 12 — four plants bought on the area figure would have nowhere to grow.

1. Mixing up centimetres and metres

The commonest mistake of all. Spacing is given in centimetres on the packet — 30 cm — but the bed is measured in metres, and the two must be in the same unit before you divide. The fix is simple: divide centimetres by 100 before you calculate. Thirty centimetres is 0.3 m, 45 cm is 0.45 m, 60 cm is 0.6 m. Write the spacing in metres next to the bed size, and check it once: if the spacing is bigger than the bed, you have mixed up the units.

2. Trusting the area method too far

The area method — bed area divided by spacing squared — is quick, and it is right when the spacing divides neatly into both sides of the bed. But it counts the leftover strips along the edges as if plants could grow in them, and on some beds that overstates the count badly. Take a bed 4 m by 1.5 m at 60 cm spacing. The area method says 6 ÷ 0.36 = 16 plants. Counting rows says the width holds 1.5 ÷ 0.6 = 2 rows, each row holds 4 ÷ 0.6 = 6 plants, and 2 × 6 = 12 plants. When the two methods disagree, trust the rows. The area figure is an upper limit, not a shopping list.

3. Forgetting the path

A bed wider than 1.2 m needs a path through it, and the path is not planting space. Take a bed 3 m by 1.2 m at 30 cm spacing, which holds 40 plants: 4 rows of 10. Put a 30 cm path across it and the planting space becomes 3 m by 0.9 m, which holds 3 rows of 10, or 30 plants. Forgetting the path overstates the count by ten plants, which is a quarter of the bed. Subtract paths, edges and anything else you will not plant before you calculate, not after.

4. Measuring edge to edge instead of centre to centre

Spacing is measured from the centre of one plant to the centre of the next, and measuring from the edge of one plant to the edge of the next leaves them too far apart. At 30 cm spacing, a lettuce with leaves 15 cm across would end up with its neighbours 45 cm away centre to centre if you measured edge to edge — half as much again as the intended gap. Mark the spacing on a stick, put the stick's mark at the centre of each plant, and the gap will be right without thinking about it.

5. Rounding up instead of down

A division that gives 4.6 rows means 4 rows, not 5, because the fifth row would sit in the leftover strip and crowd its neighbours. Rounding up is tempting when you have already bought the plants, but a plant with no room is a wasted plant: it grows small, shades its neighbours, and gives less than a plant with its full spacing. Buy the rounded-down number, add two or three spares for losses, and plant the spares in pots rather than squeezing them into the bed.

check 1: spacing in metres (30 cm = 0.3 m)
check 2: rows × plants per row, not area alone
check 3: subtract paths before calculating
check 4: centre to centre, not edge to edge
check 5: always round down

A one-minute check before you buy

Run these five checks on every bed before you order plants. Is the spacing in metres? Did you count rows, not just area? Did you subtract the path? Are you measuring centre to centre? Did you round down? If any answer is no, fix that step and recalculate.

Frequently asked questions

Why did I buy too many plants for my bed?

Usually the area method overstated the count. A 4 m by 1.5 m bed at 60 cm gives 16 by area but 12 by counting rows — trust the rows.

Can I squeeze extra plants into the leftover strip?

No. A strip narrower than the spacing cannot hold a row, and plants squeezed in will be crowded and small.

Do paths count as planting space?

No. Subtract the path before you calculate. A 30 cm path across a 3 m by 1.2 m bed cuts the count from 40 to 30 plants.

Should I round the plant count up or down?

Down. A division giving 4.6 rows means 4 rows; a plant with no room is a wasted plant.

More guides on the Plant Spacing Calculator

Try it yourself

Try the Plant Spacing Calculator — free, in your browser.

Open the Plant Spacing Calculator