← All blog posts

How to get an accurate result from the Deck Board Calculator

WhiteUI · A plain-English guide to the Deck Board Calculator

An accurate deck board count comes from four habits: measure the finished deck, use the exact board size, let the tool round only at the end, and check the answer backwards. The Deck Board Calculator already uses exact numbers, so most accuracy problems come from what is typed in — a guessed measurement, a rounded board width, or a waste figure picked at random.

At a glance

35 boards cover 17.64 sq m17.64 sq m coveredOut of 19.2 sq mNeeded with waste: 17.50 sq m
35 boards cover 17.64 square metres, more than the 17.50 square metres needed with waste.

Measure the finished deck, twice

Measure the length and width of the finished deck — the surface the boards must cover, including any overhang past the frame. Measure each side twice, from different ends, and use the larger figure if the two disagree. A deck that is 4.5 metres by 3.6 metres is 16.2 square metres, but a deck measured as 4.4 by 3.5 is 15.4 square metres — 0.8 square metres less, which is about two boards at 0.504 square metres each. Tape measures sag and decks are rarely perfectly square, so the second measurement is the one that saves the order.

Use the exact board size

Use the size printed on the board or the supplier’s listing, not a rounded guess. A board sold as 140 millimetres is 0.14 metres, but a board that actually measures 138 millimetres is 0.138 metres, and over a large deck that 2 millimetre gap adds up. For the worked example below, the boards are 0.14 metres by 3.6 metres, giving a board area of 0.504 square metres. Typing 0.15 instead would give a board area of 0.54 square metres and an answer about two boards too low.

Round only at the end

Keep the full number through the calculation and round up only once, at the end. Take a 4.5 metre by 3.6 metre deck with 0.14 metre by 3.6 metre boards and 8% waste. The deck area is 16.2 square metres and one board covers 0.504 square metres, so the exact count is 16.2 divided by 0.504, which is 32.14 boards. Add 8% waste: 32.14 times 1.08 is 34.71, rounded up to 35 boards. If you had rounded 32.14 down to 32 first, you would get 32 times 1.08, which is 34.56, rounded up to 35 — the same answer here, but on other decks an early round loses a board.

Check the answer backwards

Multiply the answer back and see if it covers the deck. Thirty-five boards at 0.504 square metres each cover 35 times 0.504, which is 17.64 square metres. The deck needs 16.2 square metres plus 8% waste, which is 16.2 times 1.08, or 17.50 square metres. Since 17.64 is more than 17.50, the 35 boards cover the deck with a small margin. If the backwards check came out below the needed area, something would be wrong — usually a mistyped width or a forgotten waste allowance.

Match the waste to the deck

Five percent suits a plain rectangle with straight cuts. Use 8% or 10% when the deck has steps, posts, an angled edge or a picture-frame border, because each of those adds cuts and offcuts. On the 4.5 by 3.6 metre deck, 5% waste would give 32.14 times 1.05, which is 33.75, rounded up to 34 boards — one fewer than the 8% figure. That one board is the margin for a single bad cut, so pick the waste that matches the job, not the smallest number.

Frequently asked questions

How do I get the most accurate deck board count?

Measure the finished deck twice, use the exact board size from the supplier, set waste to match the deck, and check the answer backwards.

How many boards does a 4.5 m by 3.6 m deck need?

35 boards with 0.14 m by 3.6 m boards and 8% waste. Deck area 16.2 square metres divided by board area 0.504 square metres is 32.14, times 1.08 is 34.71, rounded up to 35.

How do I check my answer backwards?

Multiply the board count by one board’s area. Here 35 boards times 0.504 square metres is 17.64 square metres, more than the 17.50 square metres needed with waste.

What waste should I use for a deck with steps?

8% to 10%. Steps, posts and angled edges add cuts and offcuts that a plain rectangle does not have.

More guides on the Deck Board Calculator

Try it yourself

Try the Deck Board Calculator — free, in your browser.

Open the Deck Board Calculator