Sand Calculator formula — how it actually works
Every answer on the Sand Calculator comes from four short lines of arithmetic. There is no hidden step and no table of sand types to look up. The tool takes your length, width and depth, works out the area, then the volume, then the weight, then the bags, in that order.
area = length × width volume = area × depth tonnes = volume × 1600 kg/m³ ÷ 1000 bags = tonnes × 1000 ÷ 25, rounded up
At a glance
Step one: the area
Area is length times width, in square metres. A sandpit 3 metres long and 3 metres wide has an area of 3 × 3 = 9 square metres. Area alone does not tell you how much sand you need, because a thin layer and a deep layer over the same area need very different amounts, which is why depth comes next.
Step two: the volume
Volume is area times depth, in cubic metres. For the sandpit at 0.3 metres deep, the volume is 9 × 0.3 = 2.7 cubic metres. Depth is the number people most often get wrong, because it is the smallest of the three and the easiest to misread: 0.3 metres is 30 centimetres, a deep sandpit, while 0.03 metres is only 3 centimetres, a dusting.
Step three: the weight in tonnes
The tool uses 1,600 kilograms per cubic metre for dry sand, so the weight is 2.7 × 1,600 = 4,320 kilograms, which is 4.32 tonnes. The 1,600 figure is a common value for dry sand, not a measurement of your particular sand, so treat the tonnes as an estimate that is good enough to choose between bags and bulk delivery.
Step four: the bags, rounded up
Bags are the weight divided by 25 kilograms: 4,320 ÷ 25 = 172.8, rounded up to 173 bags. The tool rounds up rather than to the nearest whole bag, because rounding 172.8 down to 173 would be right by luck, but rounding a figure like 172.2 down to 172 would leave you 20 kilograms short. Rounding up is the safe rule, applied every time.
Worked example: the tool’s starting values
With 5 metres by 2 metres at 0.1 metres deep, the area is 10 square metres, the volume is 1 cubic metre, the weight is 1.6 tonnes and the bags are 64. Each step feeds the next, so a mistake in the area carries through to the bags, which is why measuring the length and width carefully is worth more than worrying about the bag arithmetic.
The common mistake
People multiply length by width by depth in the wrong units, mixing metres and centimetres in one line. If the length is 300 centimetres and the width is 3 metres, the area is not 900 square metres. Convert every measurement to metres first, then use the four lines above, and the formula stays exact.
Frequently asked questions
What is the Sand Calculator formula?
Area = length × width, volume = area × depth, tonnes = volume × 1,600 kg/m³ ÷ 1,000, and bags = tonnes × 1,000 ÷ 25, rounded up.
How much sand does a 3 m by 3 m sandpit at 0.3 m deep need?
2.7 cubic metres, which weighs 4.32 tonnes, or 173 bags of 25 kg.
Why are the bags rounded up?
Because a fraction of a bag is still a bag you need. 172.8 bags means 173 bags, since 172 bags would leave 20 kilograms short.
How much does one cubic metre of sand weigh?
About 1.6 tonnes, or 1,600 kilograms, for dry sand. Wet sand can be heavier.
More guides on the Sand Calculator
- How to use the Sand Calculator — step by step
- Sand Calculator explained with worked examples
- Sand Calculator for beginners — start here
- Common mistakes people make with the Sand Calculator
- Sand Calculator vs doing it by hand — which is faster?
- sand calculator — the complete guide
- How to get an accurate result from the Sand Calculator
- Sand Calculator for students — with examples
- Sand Calculator for homeowners and DIYers
Try the Sand Calculator — free, in your browser.