← All blog posts

How to get an accurate result from the Sand Calculator

WhiteUI · A plain-English guide to the Sand Calculator

An accurate sand result comes from three habits: measure the ground twice, convert every measurement to metres before you type it, and add about 10 percent for sand settling into the ground. The Sand Calculator already uses exact arithmetic, so most accuracy problems come from what is typed in, not from the tool.

At a glance

Measured job: 2.496 m³ on a 0 to 5 m³ scale0 m³2.5 m³5 m³2.496 m³ = 3.99 tonnes = 160 bags
A job 6.5 metres by 3.2 metres at 0.12 metres deep needs 2.496 cubic metres of sand, just under halfway on a 0 to 5 cubic metre scale.

Measure twice, in two places

Measure the length and the width in two places each, because ground is rarely straight. If one side measures 6.5 metres at one end and 6.4 at the other, use 6.5. The same goes for depth: measure it in three places and use the largest reading, because the deepest spot decides how much sand the whole area needs.

Worked example: a measured job

Take a strip 6.5 metres long, 3.2 metres wide and 0.12 metres deep. The area is 6.5 × 3.2 = 20.8 square metres. The volume is 20.8 × 0.12 = 2.496 cubic metres. The weight is 2.496 × 1,600 = 3,993.6 kilograms, or 3.99 tonnes. The bags are 3,993.6 ÷ 25 = 159.744, rounded up to 160 bags. This is a case where the decimals matter: rounding the length down to 6 metres would give only 2.304 cubic metres, nearly 0.2 cubic metres short.

Add 10 percent for settling

Sand compacts underfoot and sinks into soft ground, so add about 10 percent before you order. For the measured job above, 2.496 × 1.1 = 2.7456 cubic metres, which is about 2.75 cubic metres. You can add it by raising the depth a little in the tool, or by multiplying the volume by 1.1 yourself. Either way, a small surplus is far cheaper than a second delivery for a quarter of a cubic metre.

Round only at the end

Keep the full decimals through the calculation and round only the final bag count. The measured job gives 159.744 bags, which rounds up to 160. If you had rounded the volume down to 2.5 cubic metres first, you would get 160 bags anyway here, but on other jobs an early rounding can move the bag count by one or two, and the error is always in the wrong direction.

Check the answer backwards

Convert the answer back to the starting numbers and see if you land where you began. From 160 bags, the weight is 160 × 25 = 4,000 kilograms, which is 4 tonnes, and 4 ÷ 1.6 = 2.5 cubic metres, which matches the 2.496 cubic metres within rounding. A gap bigger than a few kilograms would mean an input was wrong, most likely the depth.

The common mistake

People measure the depth once, in the shallowest spot. If the real depth varies from 0.1 to 0.15 metres and you measure only the 0.1 spot, you will order a third less sand than the deep end needs. Measure the depth in several places and use the largest reading, then add the 10 percent on top.

Frequently asked questions

How much sand does a 6.5 m by 3.2 m area at 0.12 m deep need?

2.496 cubic metres, which weighs 3.99 tonnes, or 160 bags of 25 kg.

How much extra sand should I add for settling?

About 10 percent. For 2.496 cubic metres, order about 2.75 cubic metres.

How do I check my sand answer?

Work backwards: 160 bags is 4,000 kg, or 4 tonnes, and 4 divided by 1.6 is 2.5 cubic metres, which should match your volume within rounding.

Why should I measure the depth in several places?

Because ground is uneven. The deepest spot decides how much sand the area needs, so use the largest depth reading.

More guides on the Sand Calculator

Try it yourself

Try the Sand Calculator — free, in your browser.

Open the Sand Calculator