← All blog posts

drywall calculator — the complete guide

WhiteUI · A plain-English guide to the Drywall Calculator

Drywall is sold by the sheet, so the whole job comes down to one question: how many sheets cover your walls? This guide covers every part of the Drywall Calculator — its three inputs, the sheet sizes, ceilings, screws and the spare sheets worth adding — so you can answer that question for any room.

At a glance

50 m² on a 0 to 100 m² scale0 m²50 m²100 m²50 m² = 18 sheets and 576 screws
Fifty square metres sits halfway along a 0 to 100 square metre scale.

The three inputs

The tool asks for three numbers. Wall or ceiling area, in square metres, is the total surface to cover. Area per sheet, in square metres, is how much one sheet covers — 2.88 m² for a standard 1.2 × 2.4 metre sheet. Screws per sheet is how many fixings each sheet takes — 32 to start with. Change any of the three and both answers update.

Sheet sizes and what they change

Sheets come in more than one length. A 1.2 × 2.4 metre sheet covers 2.88 m², a 1.2 × 2.7 metre sheet covers 3.24 m², and a 1.2 × 3.0 metre sheet covers 3.6 m². For a 40 m² wall that means 14 sheets with the standard size, 13 sheets with the 2.7 metre size (40 ÷ 3.24 = 12.35), and 12 sheets with the 3.0 metre size (40 ÷ 3.6 = 11.11). Longer sheets also mean fewer screws: 448, 416 and 384 respectively at 32 per sheet.

Ceilings count the same way

A ceiling is just a wall lying flat. Measure its length times its width and enter the area in the same box. A ceiling of 5 metres by 4 metres is 20 m², which needs 20 ÷ 2.88 = 6.94, so 7 sheets and 224 screws. If a job covers walls and a ceiling, add the areas together or run each surface separately — separate runs are safer, because offcuts from a wall may not fit a ceiling.

Worked example: a 50 m² job

For 50 m² with standard sheets: 50 ÷ 2.88 = 17.36, so 18 sheets, and 18 × 32 = 576 screws. The sheets cover 18 × 2.88 = 51.84 m², leaving 1.84 m² spare. Add a 10% allowance for cuts and mistakes and the area becomes 55 m²: 55 ÷ 2.88 = 19.10, so 20 sheets and 20 × 32 = 640 screws. Two extra sheets is a sensible cushion on a job this size.

A small job for comparison

A single wall of 15 m² needs 15 ÷ 2.88 = 5.21, so 6 sheets and 6 × 32 = 192 screws. The sheets cover 17.28 m², so there is 2.28 m² spare — plenty for one wall, which is why small jobs rarely need an extra allowance.

The common mistake

People buy exactly the number the tool shows and leave no spare. For a 40 m² wall the tool gives 14 sheets covering 40.32 m² — only 0.32 m² of spare board. One miscut sheet and the job is a sheet short, with a second trip to the yard. Add one or two spare sheets on any job where a cut goes wrong, and more if the room has awkward corners.

Frequently asked questions

What are the three inputs?

Wall or ceiling area in m², area per sheet in m² (2.88 for a standard sheet), and screws per sheet (32 to start with).

How many sheets does 50 m² need?

18 sheets and 576 screws. With a 10% waste allowance, 55 m² needs 20 sheets and 640 screws.

Do I count the ceiling separately?

You can add its area to the walls, but running it separately is safer, because wall offcuts may not fit a ceiling.

Should I buy spare sheets?

Yes, one or two on most jobs. Fourteen sheets for 40 m² cover only 40.32 m², so one bad cut leaves you short.

Does the tool estimate joint compound?

No. It counts sheets and screws only, so work out compound and tape separately.

More guides on the Drywall Calculator

Try it yourself

Try the Drywall Calculator — free, in your browser.

Open the Drywall Calculator