← All blog posts

Common mistakes when calculating dilution

WhiteUI · A plain-English guide to the Dilution Calculator

Dilution sums are short, which is why the mistakes are so easy to make: one wrong number goes in, one wrong answer comes out, and the sum itself looks fine.

Three boxes showing 62.5 millilitres of stock plus 187.5 millilitres of water making 250 millilitres of 0.5 molar solution
In plain words: 62.5 mL of 2 M stock plus 187.5 mL of water makes 250 mL of 0.5 M. Adding a full 250 mL of water instead gives 312.5 mL at 0.4 M.

Mistake 1: adding the full final volume of water

The water is the final volume minus the stock volume, never the final volume on its own. To make 250 mL of 0.5 M from 2 M stock you need 62.5 mL of stock, so the water is 250 − 62.5 = 187.5 mL. Add a full 250 mL of water on top of the stock and the total is 312.5 mL, giving a concentration of 2 × 62.5 ÷ 312.5 = 0.4 M, not 0.5 M.

Mistake 2: swapping the stock and the target

The stock concentration, C1, is always the stronger one, and it goes underneath in the division. To make 100 mL of 0.1 M from a 1 M stock, the right sum is V1 = 0.1 × 100 ÷ 1 = 10 mL. Swap the two concentrations and the sum becomes V1 = 1 × 100 ÷ 0.1 = 1,000 mL, which is ten times the final volume and plainly impossible.

Mistake 3: mixing millilitres and litres

The two volumes must use the same unit, or the answer comes out a thousand times wrong. To make 250 mL of 0.5 M from 2 M stock, keep everything in millilitres: V1 = 0.5 × 250 ÷ 2 = 62.5 mL. Enter the final volume as 0.25 L and the answer is 0.0625 L, which is the same 62.5 mL, but enter it as 250 and read the answer as litres and you get 62.5 L, a thousand times too much.

Mistake 4: forgetting the stock adds volume

The stock itself takes up space, so the finished volume includes it. Ten millilitres of 1 M stock plus 90 mL of water makes 100 mL of 0.1 M solution, because 10 + 90 = 100. Add 100 mL of water to the same 10 mL of stock and the total is 110 mL, giving a concentration of 1 × 10 ÷ 110 = 0.0909 M, which is weaker than the 0.1 M you wanted.

Mistake 5: diluting to a stronger concentration

Dilution only makes a solution weaker, so a target stronger than the stock is impossible by dilution alone. Asking for 2 M from a 1 M stock gives V1 = 2 × 100 ÷ 1 = 200 mL of stock to make 100 mL of finished solution, which cannot be done, because you cannot fit 200 mL into 100 mL.

A two-minute check before you trust an answer

Before you use a dilution answer, check that it multiplies out: C1 × V1 should equal C2 × V2, so for 250 mL of 0.5 M from 2 M stock, 2 × 62.5 = 125 and 0.5 × 250 = 125.

Frequently asked questions

What is the most common dilution mistake?

Adding the full final volume of water instead of topping up. For 250 mL of 0.5 M from 2 M stock, the water is 250 − 62.5 = 187.5 mL, not 250 mL.

Can I mix millilitres and litres in one sum?

No. Both volumes must use the same unit. 250 mL is 0.25 L, so V1 = 0.5 × 0.25 ÷ 2 = 0.0625 L, which is 62.5 mL.

What does 1:10 mean in a dilution?

1 part stock in 10 parts total, so 1 part stock and 9 parts water. 10 mL of 1 M stock plus 90 mL of water makes 100 mL of 0.1 M.

Can I dilute to a stronger concentration?

No. Dilution only makes a solution weaker. A target stronger than the stock needs a stronger stock or a different method.

More guides on the Dilution Calculator

Try it yourself

Try the Dilution Calculator — free, in your browser.

Open the Dilution Calculator