← All blog posts

Stair history: where the formula comes from

WhiteUI · A plain-English guide to stair calculation

The stair formula is not a modern standard. It is builder’s practice written down: a staircase must have equal risers, a consistent going, and a run that fits the building. The arithmetic — divide, round, re-divide — is simply the shortest way to honour those three rules at once.

Equal risers are the oldest rule. Human feet learn a staircase’s rhythm within two steps, and a single step of a different height breaks that rhythm and causes trips. That is why the formula rounds the step count and then adjusts the riser, rather than keeping the target riser and accepting an uneven final step. Comfort follows from equality, not from hitting an exact target.

The run rule — steps minus one — comes from the definition of a staircase itself. The flight ends at the upper floor, so the last rise lands on the landing rather than on another tread. Counting a tread there would overstate the run by a full tread depth, and in a tight hallway that phantom tread is the difference between fitting and not fitting.

The worked example carries the whole tradition in three lines: 300 cm at an 18 cm target gives 17 steps, 17.65 cm risers and a 432 cm run. Building regulations later codified comfortable ranges — roughly 17 to 19 cm risers — but the geometry underneath predates the regulations by centuries.

Equal risers or an even split: two ways builders used to think

Before the formula was written down, builders split a rise by eye: divide the height into roughly equal parts, build, and let the last step absorb whatever was left over. It usually looked right, and it regularly produced one step a centimetre or two different from the rest — the exact step that trips people, because feet learn a staircase’s rhythm within two steps. The modern rule does the opposite: it rounds the step count first, then adjusts every riser by the same amount, so no single step carries the leftover.

Take a 290 cm rise with a 19 cm target and 26 cm treads: 290 ÷ 19 = 15.26, rounded to 15 steps, an actual riser of 19.33 cm and a run of (15 − 1) × 26 = 364 cm. Compare that with the 300 cm example in this post — 17 steps at 17.65 cm. The taller target riser gives fewer steps but taller ones, and the choice between them is a comfort choice, not a maths choice. The maths only insists on one thing the old by-eye method did not: every riser identical.

What to check in an old staircase before you copy it

First, measure every riser, not just the first two. Old staircases often vary by a centimetre from step to step, because they were built by the by-eye method, and copying the average gives you a staircase with the same trip hazard. If the risers differ, copy the count and the total rise, not the individual steps — then let the formula produce equal risers for the same height.

Second, check the run against the room it sits in. A 364 cm run needs 3.64 metres in a straight line, and an old staircase that fits may have done so only because its treads are shallower than the 25 to 28 cm that suits most homes. Third, check the headroom and the handrail: older stairs often fail modern headroom rules even when the steps feel fine. And finally, check the regulations. The geometry underneath predates the rules by centuries, but the rules are what a building inspector measures, so a staircase that copies an old one still has to pass a new inspection.

Frequently asked questions

Why round the step count instead of using the exact division?

Because you cannot build a fraction of a step. Rounding gives a whole number of steps, and the actual riser is then adjusted so all steps are equal. Equal risers matter far more than hitting the target exactly.

Why is the total run based on steps minus one?

Because the top step is the upper floor itself: you step from the last tread onto the landing, not onto another tread. Counting an extra tread would overstate the run by one tread depth.

What riser and tread sizes suit a home staircase?

Around 17 to 19 cm with a tread of 25 to 28 cm suits most homes. Local building rules may set limits, so check them before building. This calculator does the geometry, not the regulations.

More guides on the Stair Calculator

Try it yourself

Enter your total rise, target riser and tread depth to see the step count and total run.

Open the Stair Calculator