← All blog posts

Stair for beginners: no maths background needed

WhiteUI · A plain-English guide to stair calculation

You do not need maths to plan a staircase. You need the height between the two floors, an idea of how high you want each step to be, and how deep you want each tread. The calculation turns those three wishes into a staircase that actually fits.

First, how many steps? Divide the total height by the step height you want, and round to a whole number — you cannot build half a step. A 300 cm height divided by an 18 cm target gives 16.67, so 17 steps. Second, how high is each step really? Divide the total height by the step count: 300 divided by 17 is 17.65 cm per step, near enough to the target and identical on every step.

Third, how much floor does it take? Multiply the tread depth by one fewer than the step count, because the top step is the floor above: (17 − 1) × 27 cm = 432 cm. That is the whole method, and the same steps give 16 steps, 17.50 cm risers and a 390 cm run for a 280 cm rise with 26 cm treads.

The one rule beginners should memorise is that all risers must be equal. A staircase with one odd step is a tripping hazard even if the arithmetic looks tidy, so always let the calculation adjust the riser to keep every step the same.

Calculator or tape measure first: the order that works

The tape measure comes first, always. The calculation is only as good as the rise you feed it, and a guessed rise produces a confident-looking answer that does not fit the house. Measure finished floor to finished floor, write the number down, and only then open the calculator. Take a smaller flight as an example: a 270 cm rise with a 17 cm target riser and 25 cm treads gives 270 ÷ 17 = 15.88, rounded to 16 steps, an actual riser of 16.88 cm and a run of (16 − 1) × 25 = 375 cm. Compare that with the 300 cm example in this post — 17 steps and a 432 cm run. Thirty centimetres less height means one fewer step and 57 cm less run.

That comparison is also how you sanity-check your own measurement. If your rise is close to 300 cm but your answer comes out near the 270 cm staircase, the measurement is probably wrong, not the maths. Measure twice, from both floors, and use the figure that repeats. A five-minute remeasure is cheaper than a staircase built 30 cm short.

Beginner checks that prevent a crooked staircase

First, check that all risers are equal. In the example above every step is 16.88 cm — not 17 cm on most steps and something else on the last one. A single odd step is a tripping hazard even when the arithmetic looks tidy, so always let the calculation adjust the riser to keep every step the same. Second, check the run uses steps minus one. Sixteen steps with 25 cm treads give a run of 375 cm, not 400 cm, because the top step is the floor above and needs no tread of its own.

Third, check the run fits the room: 375 cm is 3.75 metres of floor, and it has to exist in a straight line unless the staircase turns. Fourth, check the headroom at the middle of the flight, where the ceiling is lowest relative to the steps. And finally, check the rules — riser height, tread depth and handrails — with your local building authority. The calculator does the geometry; it cannot tell you what your council allows.

Frequently asked questions

Why round the step count instead of using the exact division?

Because you cannot build a fraction of a step. Rounding gives a whole number of steps, and the actual riser is then adjusted so all steps are equal. Equal risers matter far more than hitting the target exactly.

Why is the total run based on steps minus one?

Because the top step is the upper floor itself: you step from the last tread onto the landing, not onto another tread. Counting an extra tread would overstate the run by one tread depth.

What riser and tread sizes suit a home staircase?

Around 17 to 19 cm with a tread of 25 to 28 cm suits most homes. Local building rules may set limits, so check them before building. This calculator does the geometry, not the regulations.

More guides on the Stair Calculator

Try it yourself

Enter your total rise, target riser and tread depth to see the step count and total run.

Open the Stair Calculator