← All blog posts

Stair FAQ: the questions everyone asks

WhiteUI · A plain-English guide to stair calculation

Staircase questions mostly come from the same surprise: the answer is rarely the exact number you first expected. The step count gets rounded, the riser shifts slightly from the target, and the run is one tread shorter than intuition suggests. Each of those adjustments has a physical reason.

Worked example: a total rise of 300 cm with a target riser of 18 cm gives 300 ÷ 18 = 16.67, rounded to 17 steps. The actual riser is then 300 ÷ 17 = 17.65 cm, and with a tread depth of 27 cm the total run is (17 − 1) × 27 = 432 cm. A second staircase, 280 cm rise with a 17 cm target, gives 280 ÷ 17 = 16.47, rounded to 16 steps, an actual riser of 17.50 cm and a run of (16 − 1) × 26 = 390 cm with 26 cm treads.

The question about regulations deserves a direct answer. Around 17 to 19 cm risers with 25 to 28 cm treads suit most homes, but local building rules may set their own limits on riser height, tread depth, headroom and handrails. The calculator settles the geometry; the rules still need checking before you build.

And the most practical question — can I just use the target riser as the actual riser? Only if the rise divides evenly. In the example it does not: 300 divided by 18 is 16.67, not a whole staircase, so the riser must move to 17.65 cm to keep all 17 steps equal.

Steeper or shallower: how the trade-off actually works

Every staircase trades comfort against floor space, and the numbers make the trade visible. Take a taller flight: a total rise of 320 cm with an 18 cm target riser and 28 cm treads gives 320 ÷ 18 = 17.78, rounded to 18 steps, an actual riser of 17.78 cm and a total run of (18 − 1) × 28 = 476 cm. Compare that with the 300 cm example in this post — 17 steps and a 432 cm run. Twenty centimetres more height adds one step and 44 cm of run, which is nearly half a metre of extra floor.

The choice runs one way: a lower riser means more steps and a longer run, so the staircase is easier to climb but takes more of the room; a higher riser means fewer steps and a shorter run, but each step is a bigger lift. If floor space is tight, accept a riser near 19 cm and keep the run short. If the stairs will be used by older people or small children, aim near 17 cm and find the extra run somewhere — comfort is hard to add later, and a staircase that is tiring on day one stays tiring.

What to check before you trust the numbers

First, check the rise is measured finished floor to finished floor, including the thickness of the flooring on both levels. A measurement taken to bare concrete will be wrong by the thickness of the tiles or boards, and the whole staircase inherits the error. Second, check the run fits the room: the 476 cm run in the example above is 4.76 metres of floor, and a hallway shorter than that means the staircase as calculated simply does not fit.

Third, check the headroom where the staircase passes under the floor above — the geometry can be perfect while your head is not. Fourth, check local building rules for riser height, tread depth, headroom and handrails before you build; the calculator settles the geometry, and the rules still need a separate check. Finally, write the three results down — steps, actual riser and run — and check each against common sense. Eighteen steps at 17.78 cm with a 476 cm run is a believable staircase; a run a tread too long is not.

Frequently asked questions

Why does the step count get rounded?

Because you cannot build a fraction of a step. Rounding to a whole number and then adjusting the riser keeps every step equal.

Why is the run based on steps minus one?

The top step is the upper floor itself. You step from the last tread onto the landing, so there is one fewer tread than steps.

What riser and tread sizes feel comfortable?

Around 17 to 19 cm risers with 25 to 28 cm treads suit most homes. Check local building rules before building.

Does the calculator cover building regulations?

No. It does the geometry — steps, riser and run. Headroom, handrails and legal limits still need a separate check.

More guides on the Stair Calculator

Try it yourself

Enter your total rise, target riser and tread depth to see the step count and total run.

Open the Stair Calculator