Cone volume formula explained with an example
The cone volume formula is V = (1/3) × π × r² × h. It looks short, but each part does a clear job, and once you see what each part is for, the formula is easy to remember and hard to get wrong.
What each part of the formula does
The π × r² part is the area of the round base. A circle’s area is π times its radius squared, so for a radius of 5 cm the base covers 78.54 square cm. Multiplying by h stretches that base into a cylinder of the same height — a tube with the same round footprint. The (1/3) at the front then shrinks that tube down to a cone, because a cone tapers to a point and holds exactly one third of the cylinder it sits inside.
Worked example
Take a cone with radius 5 cm and height 12 cm.
Base area: π × 5² = π × 25 = 78.54 Cylinder: 78.54 × 12 = 942.48 Cone volume: 942.48 ÷ 3 = 314.16 Volume = 314.16 cubic cm
As a check, the slant height is exactly 13 cm, since √(5² + 12²) = √169 = 13 — the familiar 5-12-13 triangle. The curved surface area is π × 5 × 13 = 204.20 square cm.
A cone with radius 5 cm and height 12 cm. Its volume is 314.16 cubic cm.
Why the answer is smaller than the cylinder
People sometimes expect the cone to hold about half the cylinder. It holds a third, which feels small until you picture it: the cone is full width only at the very bottom and narrows all the way to a point, so most of the cylinder’s space is empty air around the cone’s sloping sides. If your answer comes out close to the cylinder’s volume, you have probably forgotten the divide-by-3 step — here that would give 942.48 instead of 314.16.
Doubling the radius or doubling the height: which matters more
The radius is squared in the formula, so it matters far more than the height. The cone in the worked example — radius 5 cm, height 12 cm — holds 314.16 cubic cm. Double the height to 24 cm and the volume doubles to 628.32 cubic cm. But double the radius to 10 cm, keeping the height at 12 cm, and the volume becomes (1/3) × π × 100 × 12 = 1,256.64 cubic cm — four times the original. A wide cone holds far more than a tall one.
That is worth knowing when you are choosing a container. A funnel twice as wide holds four times as much, so a small increase in width buys a lot of capacity, while extra height buys only a proportional amount. If a cone must hold a set volume, widen it first and lengthen it second.
A cone with a radius of 5 cm and a height of 6 cm holds half the worked example’s volume — (1/3) × π × 25 × 6 = 157.08 cubic cm — because halving the height halves the volume, while halving the radius would quarter it.
The mistake that shrinks the answer five times
The easiest slip in this formula is forgetting to square the radius — using 5 instead of 25. For the cone above, that gives (1/3) × π × 5 × 12 = 62.83 cubic cm instead of 314.16, exactly five times too small. The error is easy to miss because 62.83 still looks like a plausible volume for a small cone.
The check is to square first and write the squared number down before doing anything else: 5² = 25, then π × 25 = 78.54, then × 12 = 942.48, then ÷ 3 = 314.16. And the cylinder test catches it too: the cylinder here is 942.48 cubic cm, and the cone must be a third of it. If your answer is nowhere near a third of the cylinder, re-do the squaring step.
Frequently asked questions
Why is there a ⅓ in the formula?
Because a cone holds exactly one third of the volume of a cylinder with the same base and height. The formula first works out that cylinder (π × r² × h) and then takes a third of it.
Can I use the diameter instead of the radius?
No — halve it first. A diameter of 10 cm means a radius of 5 cm. Using 10 as r would square to 100 instead of 25 and give an answer four times too big.
Does the formula work for a cone lying on its side?
Yes. The h in the formula is the perpendicular height from the base to the tip, not the length along the slope. A cone tipped over still has the same perpendicular height, so the volume is unchanged.
More guides on the Cone Volume Calculator
- How to calculate cone volume step by step
- Cone volume: a worked example from start to finish
- Cone volume mistakes most people make
- Cone volume for beginners: no maths background needed
- Cone volume FAQ: the questions everyone asks
- Cone volume on mobile: doing it without an app
- Cone volume shortcut method for quick answers
- Cone volume with units: converting inputs correctly
- Cone volume history: where the formula comes from
Volume, slant height and lateral area from radius and height — free, in your browser.