← All blog posts

Text to Speech Reader formula — how it actually works

WhiteUI · A plain-English guide to the Text to Speech Reader

There is no secret formula behind the Text to Speech Reader — and that is the honest point of this guide. A calculator like an EMI calculator hides a formula with interest and powers. This tool has one division, one speed, and a voice that already lives on your device. The reading time is words ÷ 150 words a minute, and the rate slider multiplies that 150. Below is exactly how the number is made, where it can drift, and how to check it yourself.

The reading-time formula: minutes equals words divided by 150 times the rate, with 300 words taking 4 minutes at half speed, 2 at normal, 1 at double
In plain words: Minutes = words ÷ (150 × rate). A 300-word passage takes 4 minutes at 0.5×, 2 minutes at 1×, and 1 minute at 2×.

The one formula

Reading time in minutes = words ÷ (150 × rate). At the normal rate of 1×, that is simply words ÷ 150. The 150 is a normal speaking pace: most people read aloud at 140 to 160 words a minute, and 150 sits in the middle. The tool counts words as letter sequences, so “don’t” is one word and “well-known” is two. It does not count punctuation, and it does not count the spaces between words.

Worked example: 300 words at three rates

Take a 300-word passage. At 1× the time is 300 ÷ (150 × 1) = 2 minutes. At 0.5× it is 300 ÷ (150 × 0.5) = 300 ÷ 75 = 4 minutes. At 2× it is 300 ÷ (150 × 2) = 300 ÷ 300 = 1 minute. At 1.5× it is 300 ÷ 225 = 1.33 minutes, or 1 minute 20 seconds. The same numbers appear on the tool if you paste 300 words and move the slider: 4.0, 2.0 and 1.0 minutes.

Worked example: 450 words at 1.5×

Take a 450-word passage — a long email, say — and set the rate to 1.5×. The formula gives 450 ÷ (150 × 1.5) = 450 ÷ 225 = 2 minutes exactly. At 1× the same passage takes 3 minutes, because 450 ÷ 150 = 3. At 0.5× it takes 6 minutes, because 450 ÷ 75 = 6. The pattern is plain: doubling the words doubles the time, and doubling the rate halves it.

Where the speech actually comes from

The formula only sets the time shown on screen. The sound comes from your browser’s SpeechSynthesis system, which turns the text into speech on your device. No text is sent to a server, no audio file is made, and nothing is recorded. That is why the list of voices differs between browsers: Chrome and Edge usually offer several, while some browsers offer only the system default.

Where the estimate can drift

The formula treats every word as equal, but real speech is not that tidy. A voice pauses at full stops and commas, so a 300-word passage made of short sentences runs a few seconds longer than 2 minutes. Numbers, web addresses and abbreviations are read letter by letter or spelled out, which also adds seconds. Treat the shown time as close, not exact: for a 2-minute passage, expect the real reading to land within about 10 seconds of it.

The common mistake

People treat 150 words a minute as a promise and then complain the reading ran 8 seconds over. It is an average, not a clock. A passage of long words and short sentences reads slower than one of short words and long sentences, even at the same word count. If the timing matters — a speech, for instance — time the real reading once and use that, not the estimate.

Frequently asked questions

What is the reading-time formula?

Minutes = words ÷ (150 × rate). At normal speed, 1×, that is simply words ÷ 150.

Why 150 words a minute?

Most people read aloud at 140 to 160 words a minute. 150 is the middle of that range, so it fits most voices.

Does the formula count punctuation?

No. Only words are counted. Punctuation adds small pauses in the real reading, so long passages run a few seconds over the estimate.

Is any of my text sent to a server?

No. The speech is made on your device by your browser, and the word count is done in the page. Nothing leaves the browser.

More guides on the Text to Speech Reader

Try it yourself

Try the Text to Speech Reader — free, in your browser.

Open the Text to Speech Reader