How to get an accurate result from the Text to Speech Reader
An accurate result from the Text to Speech Reader rests on two numbers: the word count and the rate. Get either one wrong and the reading time is wrong with it. This guide shows how to check both, how to clean your text so the count is honest, and how to test the result against a real reading — so the time on screen matches the time in your ears.
Step 1: check the word count
Read the big number before you trust the time. The tool counts letter sequences, so “don’t” is one word and “well-known” is two. A pasted web address can add a dozen words you never meant to count, and a block of numbers adds more. For a 500-word speech, the tool should show 500 words. If it shows 512, find the 12 extra words — usually links or reference numbers — and delete them before you trust the time.
Step 2: clean the text
Strip out anything that is not meant to be heard. Delete web addresses, order numbers and table data. Write abbreviations in full: “Dr.” becomes “Doctor”, “Rs.” becomes “Rupees”, “e.g.” becomes “for example”. Replace symbols with words where it matters: “&” becomes “and”. A clean 500-word passage reads in 3 minutes 20 seconds at 1×, because 500 ÷ 150 = 3.33 minutes. The same passage with ten links in it still shows 3 minutes 20 seconds, but sounds far longer.
Step 3: set the rate before you measure
The rate must be set before you press Speak, because a change made mid-reading applies only to the next press of Speak. For an accurate timing, use 1×: it is the normal pace the 150 words a minute is based on. At 1×, 500 words takes 3 minutes 20 seconds. At 1.5× the same passage takes 2 minutes 13 seconds, because 500 ÷ 225 = 2.22 minutes. At 2× it takes 1 minute 40 seconds, because 500 ÷ 300 = 1.67 minutes. Measure at the rate you will actually use.
Step 4: time a real reading
Trust, then check. Paste a 500-word passage, set 1×, and time the real reading with a stopwatch. The estimate says 3 minutes 20 seconds. A passage of short sentences and long words may run 10 seconds over, because voices pause at full stops; a passage of short words and long sentences may run a few seconds under. If your timed reading is 3 minutes 30 seconds, use 3 minutes 30 seconds for planning — the real reading beats the estimate every time.
Worked example: a 500-word speech
You have a speech of 500 words and 5 minutes on stage. The tool counts 500 words and shows 3 minutes 20 seconds at 1×, because 500 ÷ 150 = 3.33 minutes. That leaves 1 minute 40 seconds spare — room for pauses and a slow start. Now guess the count instead: if you assume 400 words, the estimate is 2 minutes 40 seconds, which is 40 seconds short of the truth. A 40-second error on stage is the difference between finishing calmly and being cut off mid-sentence.
The common mistake
The common mistake is counting characters instead of words. A 500-word speech is about 3,000 characters, and people who divide 3,000 by 150 get 20 minutes — six times too long. Characters are not words, and the tool’s formula divides words, not characters. Always read the word count on screen, never guess it from the character count, and never trust a time worked out from characters.
Frequently asked questions
How do I know the word count is right?
Check the big number against your text. Links and reference numbers inflate it — delete them and watch the count fall.
Which rate gives the most accurate time?
1×. The 150 words a minute behind the estimate is a normal speaking pace, so the estimate is closest at normal speed.
Why did my real reading run longer than the estimate?
Voices pause at punctuation, so short sentences and long words add seconds. Time one real reading and use that figure instead.
Can I trust the time for a speech?
As a first estimate, yes. For a stage deadline, time the real reading once — a 500-word speech is 3 minutes 20 seconds on paper, 3 minutes 30 seconds in practice.
More guides on the Text to Speech Reader
- How to use the Text to Speech Reader — step by step
- Text to Speech Reader explained with worked examples
- Text to Speech Reader formula — how it actually works
- Text to Speech Reader for beginners — start here
- Common mistakes people make with the Text to Speech Reader
- Text to Speech Reader vs doing it by hand — which is faster?
- Text to Speech — the complete guide
- Text to Speech Reader for students — with examples
- Text to Speech Reader for homeowners and DIYers
Try the Text to Speech Reader — free, in your browser.