← All blog posts

How to use the Text to Speech Reader — step by step

WhiteUI · A plain-English guide to the Text to Speech Reader

Some text is easier to hear than to read: a long email while your hands are busy, a draft you want to check by ear, or a page in a language you are still learning. The Text to Speech Reader reads any text aloud in your browser, using the voices already installed on your device. Nothing is uploaded, no account is needed, and there is no audio file to save. Open it and it already holds a welcome message of 22 words. The five steps below take you from there to hearing your own text.

Five numbered steps: paste text, pick a voice, set the rate, press Speak, listen
In plain words: Paste your text, pick a voice, set the rate, press Speak — the tool reads it aloud on your device.

Step 1: open the tool and read the starting result

The big number reads 22 words. The line below says the text takes about 0.1 minutes to read at a normal pace, which works out as 22 ÷ 150 = 0.15 minutes, or about 9 seconds. The rate shows 1×. That starting result is a real count of the welcome text, not a placeholder, and it shows the three things the tool always gives you: a word count, a reading time, and a rate.

Step 2: clear the box and paste your own text

Select the welcome text, delete it, and paste yours in its place, or just start typing. The word count and reading time update as you type, because the tool counts in your browser with every keystroke. Nothing is uploaded, stored or logged, so a private note, a draft email or a message is safe to paste in.

Step 3: pick a voice

The voice list holds the voices your browser and device already have. Chrome and Edge usually offer several, in more than one accent; some browsers offer only the system default. Try two or three and pick the clearest one for the text you are hearing. The tool never picks a voice for you.

Step 4: set the speaking rate

The slider runs from 0.5× to 2×, and the number box beside it stays in step with the slider. At 1× the tool reads at a normal pace of about 150 words a minute. A 300-word passage takes 2 minutes at 1×, 4 minutes at 0.5×, and 1 minute at 2×. Start at 1× and move up only if the voice stays clear.

Step 5: press Speak, and Stop to end early

Speak starts reading from the first word; Stop ends it at once. The status line says “Reading aloud…” while it reads, and “Finished reading.” when it reaches the end. Press Speak again to hear it from the start. If you close the tab, the reading stops with it, because the speech is made by the browser.

Worked example

Paste in a 300-word passage — about a page of a book — at 1×. The tool counts 300 words and the reading time reads 2.0 minutes, because 300 ÷ 150 = 2. At 0.5× the same passage takes 4 minutes, because 300 ÷ 75 = 4. At 2× it takes 1 minute, because 300 ÷ 300 = 1. A 150-word note takes 1 minute at 1× and 30 seconds at 2×, since 150 ÷ 300 = 0.5 minutes.

The common mistake

The usual mistake is pressing Speak with an empty box. The tool answers “Type some text first.” and stays silent, which looks like a fault but is not. The second is closing the tab mid-reading and expecting the voice to carry on: the speech is made by the browser, so it ends when the page does.

Frequently asked questions

What does the tool show when it opens?

22 words, about 0.1 minutes to read at a normal pace, and a rate of 1×, counted from the 22-word welcome text.

How do I hear my own text?

Clear the welcome text, paste yours, pick a voice and press Speak. The reading starts at once.

Can I change the speed while it reads?

Set the rate before you press Speak. A change made mid-reading applies the next time you press Speak.

Is my text sent anywhere?

No. The speech is made on your device by your browser. Nothing is uploaded, stored or logged.

More guides on the Text to Speech Reader

Try it yourself

Try the Text to Speech Reader — free, in your browser.

Open the Text to Speech Reader