← All tools/Tools/Home & DIY/Grout Calculator
Grout Calculator
How much grout your tiling job needs — from tile size, joint width and depth, and the area.
Grout needed (with waste)
How the number is worked out
How it works
Each tile contributes two edges of joint, so joint length per tile = tile length + tile width. Tiles per m² = 1 ÷ (tile length × tile width), in metres. Joint volume per m² = tiles per m² × (length + width) × joint width × joint depth. Grout weight = joint volume × density 1.6 kg per litre (typical cement grout). Total = weight × tiled area, then add the waste allowance (10% is standard).
The formula counts joints, not tiles. Each tile contributes two edges of joint — one along its length and one along its width — so the joint length per tile is its length plus its width, in metres. Tiles per square metre is one divided by the area of a single tile, so a 30 cm by 30 cm tile gives 1 ÷ 0.09 = 11.11 tiles per square metre. Multiplying tiles per square metre by the joint length per tile gives the total metres of joint in one square metre of floor. That length, times the joint width and depth in metres, is the joint volume per square metre, and multiplying by 1,000 turns cubic metres into litres. Cement grout weighs about 1.6 kg per litre, so the volume times 1.6 is the weight of grout per square metre; multiply by the tiled area, add the waste allowance, and you have the weight to buy.
Worked example: 30 × 30 cm tiles give 1 ÷ 0.09 = 11.11 tiles per m², each contributing 0.60 m of joint, so 6.67 m of joint per m². At 3 mm wide and 10 mm deep that is 0.20 litres per m², or 0.32 kg per m² at 1.6 kg per litre. For 10 m² that is 3.20 kg, and with a 10% waste allowance 3.52 kg — buy 4 kg. With 60 × 60 cm tiles, 2 mm joints, 8 mm deep and 20 m², the answer is 1.71 kg, or 1.88 kg with waste — buy 2 kg.
Second worked example: a bathroom floor in a Chennai flat, 25 m² of 45 × 45 cm tiles with 3 mm joints, 12 mm deep, and a 15% waste allowance. There are 1 ÷ 0.2025 = 4.94 tiles per m², each contributing 0.90 m of joint, so 4.44 m of joint per m². The joint volume is 4.44 × 0.003 × 0.012 × 1,000 = 0.16 litres per m², which weighs 0.16 × 1.6 = 0.26 kg per m². For 25 m² that is 6.40 kg, and with 15% waste it is 7.36 kg — buy 8 kg, which is one 5 kg bag plus three 1 kg bags, or two 5 kg bags with some left over.
Common mistakes
The most common mistake is entering the joint depth as the tile thickness without checking: the joint is usually filled to the full tile thickness, so a 12 mm tile means a 12 mm joint; on an uneven bed, joints can be deeper in places. The second is measuring the area as the room size instead of the tiled area — subtract the bath, shower tray and fixed units first.
Mix in small batches: grout starts to set in 20–30 minutes, and a stiffened batch is wasted. The fourth is using unsanded grout in wide joints: above 6 mm, unsanded grout shrinks and cracks, so switch to sanded grout.
Frequently asked questions
What density does this use?
1.6 kg per litre, typical for cement-based grout. Epoxy grout is denser — around 1.8 kg per litre — so check the pack and adjust the result up if yours is heavier. The density also varies slightly between brands, so if your pack states a coverage figure, such as kilograms per square metre for your tile size, use that instead of this estimate.
Does tile thickness matter?
Only through joint depth: the joint is usually filled to the full tile thickness, so use the tile thickness as the joint depth. A thicker tile therefore needs more grout, not because the tile is bigger but because the joint is deeper. If your tiles are uneven in thickness, use the thickest tile as the depth, or the shallow joints will be underfilled.
Why add 10% waste?
For spillage, mixing loss and cuts around edges. Grout is mixed in batches and some always sets in the bucket, and the edges of a room need more cutting and filling than the middle. For small areas or a first attempt, 15% is safer — raise the waste allowance above. On a large, simple floor with an experienced tiler, 10% is usually enough.
What if my joints are wider?
Grout needed grows with joint width: doubling the width doubles the grout, because the joint volume is width times depth times length. Wide joints (over 6 mm) also need sanded grout rather than unsanded, since unsanded grout shrinks and cracks as it dries in a wide gap. Check the pack — most sanded grouts state a minimum and maximum joint width.
How much grout comes in a bag?
Commonly 1 kg, 5 kg and 20 kg bags. This calculator rounds up to the next whole kilogram so you can match bag sizes. For a small bathroom, one or two 5 kg bags usually cover it; for a large floor, a 20 kg bag works out cheaper per kilogram. Buy the next size up rather than the exact weight — grout keeps for months if the bag stays sealed and dry.
More tools
Tell us what you think
Loving this tool, or stuck on something? Tell us — it takes a minute.
We’ll only use your name and email to reply if needed. The tool and page are filled in for you.