← All tools/Tools/Home & DIY/Asphalt Calculator

Asphalt Calculator

Asphalt volume and tonnage for your driveway or path.

m
m
cm

Asphalt needed

—

Volume
Tonnage

How it works

Volume (m³) = length (m) × width (m) × depth (m)
Tonnes = volume × 2.4 t/m³ (typical compacted density)

Length, width and depth are the only three measurements the formula needs, and all three must be in the same unit system before you multiply — the calculator takes length and width in metres and depth in centimetres, then converts depth to metres by dividing by 100. A depth of 5 cm is therefore 0.05 m, and a 10 m by 3 m strip at that depth is 1.5 cubic metres of asphalt. The second line turns volume into weight: compacted asphalt weighs about 2.4 tonnes per cubic metre, so multiplying the volume by 2.4 gives the tonnage to order. The formula works for any flat rectangle — a driveway, a path, a parking bay — but it does not allow for slopes, curved edges or an uneven base, so add 5–10% extra for those.

Worked example: 10 m × 3 m at 5 cm (0.05 m) deep is 1.5 m³, weighing about 1.5 × 2.4 = 3.6 tonnes — one small truckload at 20 tonnes capacity.

Second worked example: a parking bay 6 m long and 3.5 m wide, laid 7.5 cm (0.075 m) deep. The volume is 6 × 3.5 × 0.075 = 1.575 m³, and the weight is 1.575 × 2.4 = 3.78 tonnes — one small truckload at 20 tonnes capacity. On a first-time base with uneven ground, add 10% and order 4.16 tonnes, rounded up to about 4.2 tonnes.

What the result means

The tonnage is the weight of asphalt to order, and the volume is what it covers once rolled. A result of 3.78 tonnes for a 6 m by 3.5 m bay means roughly four tonnes of hot mix, which a supplier will usually deliver as a single small load — most trucks carry 20 tonnes. Asphalt also compacts by roughly a fifth as it is rolled, so a 7.5 cm loose layer finishes at about 6 cm — lay it deeper if the finished depth must be exactly 7.5 cm.

Check the depth figure before ordering — doubling the depth doubles the tonnage and the bill. For a driveway that takes cars every day, 5–7.5 cm over a sound base is the usual range; go thicker only if heavy vehicles will use it.

Frequently asked questions

Why 2.4 tonnes per cubic metre?

It is the typical density of compacted asphalt; loose asphalt is lighter, so order by compacted volume. The figure assumes the asphalt has been rolled and compacted — a loose layer straight from the truck weighs less per cubic metre, so ordering by loose volume would leave you short once it is rolled.

Should I add extra?

Yes — add 5–10% for uneven ground and compaction, especially on a first-time base. A base that has never been laid is rarely perfectly level, and the extra covers dips and edges that the flat calculation misses. On a well-prepared, level base, 5% is usually enough.

How many truckloads is that?

Divide tonnes by your truck’s capacity (often 20 tonnes) and round up. A 4 tonne order is one small load, while a 42 tonne road section needs three 20 tonne loads. Check the capacity with your supplier before ordering — smaller tipper trucks often carry 10 tonnes, not 20.

What depth should asphalt be for a driveway?

For a home driveway that takes cars, 5 to 7.5 cm of compacted asphalt over a properly prepared stone base is the usual range. Footpaths and light-use areas can be 4 to 5 cm. If lorries or heavy vehicles will use the surface regularly, go to 10 cm or more and check with your contractor — depth is the biggest driver of tonnage and cost.

Can I use this calculator for a road or car park?

Yes, as long as the area is a rectangle you can measure in metres. For a long road, work in sections — a 100 m stretch of 3.5 m wide road at 5 cm deep is 17.5 m³, or 42 tonnes — and add 5–10% for uneven ground. For curved or irregular shapes, split the area into rectangles and add the results together.

More tools

Tell us what you think

Loving this tool, or stuck on something? Tell us — it takes a minute.

We’ll only use your name and email to reply if needed. The tool and page are filled in for you.