← All tools/Converters/Torque/Torque Converter

Torque Converter

Convert a torque value between newton-metres, foot-pounds, inch-pounds and kilogram-force metres — all four at once.

N·m

Conversion is exact arithmetic on fixed factors — no live data, no rounding tricks. Torque wrenches are often marked in both N·m and ft·lb.

In newton-metres

—

Conversion factors

1 N·m = 0.7376 ft·lb = 8.8507 in·lb = 0.1020 kgf·m. To convert, first change the value into N·m, then divide by the target unit’s factor.

How it works

Convert through newton-metres:
1 N·m = 0.7376 ft·lb = 8.8507 in·lb = 0.1020 kgf·m
1 ft·lb = 1.35582 N·m; 1 in·lb = 0.112985 N·m;
1 kgf·m = 9.80665 N·m

Every conversion goes through newton-metres, the SI unit of torque. First the value is changed into newton-metres using the factor for its unit, then it is divided by the factor for the target unit. One newton-metre equals 0.7376 foot-pounds, 8.8507 inch-pounds and 0.1020 kilogram-force metres; going the other way, one foot-pound is 1.35582 newton-metres, one inch-pound is 0.112985 and one kilogram-force metre is 9.80665. These factors are fixed definitions, so the conversion is exact arithmetic and the only rounding is the two decimal places shown on screen. The method applies to any torque value, from a small scooter engine to a truck wheel nut.

This converts torque units — to calculate torque, use the Torque Calculator.

Worked example: 100 N·m = 100 × 0.7376 = 73.76 ft·lb, and 100 × 8.8507 = 885.07 in·lb, and 100 × 0.1020 = 10.20 kgf·m. Going the other way, 50 ft·lb ÷ 0.7376 = 67.79 N·m.

Second worked example: a car wheel nut tightened to 25 N·m. In foot-pounds that is 25 × 0.7376 = 18.44 ft·lb; in inch-pounds it is 25 × 8.8507 = 221.27 in·lb; and in kilogram-force metres it is 25 × 0.1020 = 2.55 kgf·m. Going the other way, an American manual that calls for 120 ft·lb means 120 × 1.35582 = 162.70 N·m. The inch-pound figure is always twelve times the foot-pound figure, because there are twelve inches in a foot.

Common mistakes

The costliest mistake is mixing up inch-pounds and foot-pounds: a manual that says 120 ft·lb needs 1,440 in·lb, and entering 120 in·lb instead under-tightens the bolt by twelve times, which can work loose on the road. A second mistake is confusing kilogram-force metres with newton-metres — one kgf·m is about 9.81 N·m, so the numbers look similar but the units are ten times apart. A third is treating torque like work or energy: a newton-metre of torque and a joule share the same dimensions, but torque is a twist and energy is work done, and the numbers are not interchangeable. Always check which unit the manual prints before setting the wrench.

Frequently asked questions

What is torque, in plain words?

A twisting force — how hard something is being turned. Tightening a bolt with a spanner is torque: the force on the handle times the handle’s length. Push twice as hard, or use a handle twice as long, and the torque doubles. Engines are rated in torque because it describes the twisting effort they can deliver, which is what actually turns the wheels.

Why do torque wrenches show two units?

Because car manuals differ by region. European and Asian manuals usually give N·m; American manuals often give ft·lb. The converter lets you follow either one. Many torque wrenches print both scales side by side, but the two scales are easy to misread at a glance, so converting first and setting one clear number is safer than guessing between them.

Is ft·lb the same as lb·ft?

Yes — foot-pounds and pound-feet are the same unit, just written in a different order. Both equal 1.35582 N·m. The order only reflects habit: physicists tend to write pound-feet, while car manuals and torque wrenches usually write foot-pounds. Either way, the number means the same twisting force, so convert it the same way.

What is kgf·m?

Kilogram-force metres, an older unit still used for small engines and scooters. One kgf·m is the torque from a one-kilogram weight on a one-metre lever — 9.80665 N·m. It survives in older Indian and Japanese two-wheeler manuals, where torque figures are small and the unit gives tidy numbers such as 2.5 kgf·m instead of 24.5 N·m.

Are these conversions exact?

The factors are fixed definitions, so the conversion is exact arithmetic — the only rounding is the two decimal places shown on screen. A foot-pound is defined as exactly 1.3558179483314004 newton-metres, and the converter rounds that to 1.35582 for display. Two decimal places are plenty for a torque wrench, which is rarely more accurate than a few percent anyway.

More tools

Tell us what you think

Loving this tool, or stuck on something? Tell us — it takes a minute.

We’ll only use your name and email to reply if needed. The tool and page are filled in for you.