← All tools/Calculators/Chemistry/Titration Calculator
Titration Calculator
The unknown concentration from a titration — one known solution, two volumes, one answer.
Unknown concentration (M₂)
How it works
At the equivalence point: M₁ × V₁ = M₂ × V₂. M₂ = (M₁ × V₁) ÷ V₂. M is concentration in mol/L, V is volume — use the same volume unit (mL) on both sides. This form is for a 1:1 reaction (for example HCl + NaOH). For other ratios, multiply by the mole ratio from the balanced equation.
At the equivalence point, the moles of acid and the moles of base are exactly equal — for a reaction where one acid molecule meets one base molecule. Moles equal concentration × volume, so M₁ × V₁ = M₂ × V₂, with M in moles per litre and V in millilitres on both sides. The subscript 1 is the solution whose concentration you know — the titrant in the burette — and 2 is the unknown in the flask. Rearranging gives the unknown concentration directly. The volumes must share a unit: mixing millilitres with litres throws the answer off by a factor of 1,000. The simple form assumes a 1:1 reaction, like hydrochloric acid with sodium hydroxide. For a reaction with a different ratio, such as sulfuric acid needing two sodium hydroxides, multiply one side by the ratio from the balanced equation. It also assumes the endpoint — the colour change — lands on the equivalence point, which a well-chosen indicator makes nearly true.
Worked example: 25 mL of 0.1 mol/L acid neutralises 20 mL of an unknown base. The unknown concentration is (0.1 × 25) ÷ 20 = 0.125 mol/L. If 30 mL of the acid had been needed instead, the base would be (0.1 × 30) ÷ 20 = 0.15 mol/L.
Second worked example: finding the strength of the vinegar in a kitchen bottle. You pipette 10 mL of vinegar into a flask and titrate it with 0.1 mol/L sodium hydroxide; the phenolphthalein turns pink after 12.5 mL. The vinegar’s concentration is (0.1 × 12.5) ÷ 10 = 0.125 mol/L. A standard white vinegar is about 5% acetic acid, roughly 0.8 mol/L, so a reading of 0.125 mol/L means this bottle is much weaker — most likely a diluted or mild rice vinegar.
What the result means
The number is only as good as the endpoint. Read the burette at the bottom of the meniscus, at eye level, to the nearest 0.05 mL — reading from above can shift the volume by 0.2 mL, which on a 12.5 mL titration is nearly a 2% error. Add the titrant drop by drop near the end: one extra drop, about 0.05 mL, is a small error, but a careless splash of half a millilitre is a 4% error on the same titration. Run the titration three times and average the volumes that agree within 0.1 mL; a single run is a guess, not a measurement. If the volumes scatter widely, the usual cause is a burette that was not rinsed with the titrant first — the first few millilitres get diluted by the water left inside. And remember what the answer is: the concentration of the solution in the flask, not of the titrant — swapping the two gives the reciprocal of the right answer.
Frequently asked questions
What is the equivalence point?
The point in a titration where exactly enough titrant has been added to react with all of the unknown solution — the moles of acid equal the moles of base (for a 1:1 reaction). The indicator changes colour right there.
Why must both volumes use the same unit?
Because the equation only balances if V₁ and V₂ are in the same unit — both in mL or both in L. Mixing mL and L throws the answer off by a factor of 1,000.
What if the reaction is not 1:1?
Use the mole ratio from the balanced equation. For H₂SO₄ + 2 NaOH, two moles of base react with one mole of acid, so M₁ × V₁ = 2 × M₂ × V₂ — divide the acid side by 2, or multiply the base side by 2.
How do I know which solution is the titrant?
The titrant is the solution of known concentration in the burette. The unknown goes in the flask below, with a few drops of indicator, and you add titrant until the colour changes.
What is the difference between endpoint and equivalence point?
The equivalence point is the exact chemical balance; the endpoint is where the indicator visibly changes colour. A good indicator changes colour right at the equivalence point, so the two nearly coincide.
More tools
Tell us what you think
Loving this tool, or stuck on something? Tell us — it takes a minute.
We’ll only use your name and email to reply if needed. The tool and page are filled in for you.