← All tools/Calculators/Chemistry/Percent Yield Calculator

Percent Yield Calculator

How much of the theoretical yield you actually got — as a percentage, with the loss in plain numbers.

g
g

Percent yield

—

Actual yieldLost

How it works

Percent yield = (actual yield ÷ theoretical yield) × 100.
Theoretical yield is the most the balanced equation says the reaction can make, from the limiting reactant.
Loss = theoretical yield − actual yield.

Percent yield compares what you actually recovered with the most the reaction could ever make. The theoretical yield is that maximum, worked out from the balanced equation and the limiting reactant — the reactant that runs out first — and it assumes the reaction goes to completion with no losses at all. The actual yield is what you weighed after filtering, drying and purifying, in the same units as the theoretical yield, usually grams. Dividing the actual by the theoretical and multiplying by 100 gives the percentage; the loss is simply the difference between the two. The formula says nothing about purity — an impure product can give a yield over 100% — and it says nothing about why material was lost. It applies to any reaction with a known balanced equation; without one, there is no theoretical yield to compare against.

Worked example: a reaction should make 10 g by the equation, but you recover 8 g — the percent yield is (8 ÷ 10) × 100 = 80%, and 2 g was lost. If you recover 12.5 g from a 15 g theoretical yield, the percent yield is (12.5 ÷ 15) × 100 = 83.33%.

Second worked example: a school chemistry practical making copper sulfate crystals, where the equation says 25 g is the most that can form. The class recovers 19.5 g of dry crystals, so the percent yield is (19.5 ÷ 25) × 100 = 78.00%, and the loss is 25 − 19.5 = 5.5 g. The missing 5.5 g stayed in the filtrate, on the filter paper and in the evaporating dish — normal for a first attempt, and a class that recovers 22 g next time has raised its yield to 88%.

Common mistakes

The biggest mistake is weighing the product wet. Crystals straight from the filter paper carry water, and a wet 21 g can dry down to 19.5 g — enough to turn a real 78% yield into a flattering 84%. Dry to a constant mass: weigh, dry, weigh again, and stop only when the mass stops changing. The second mistake is using the wrong limiting reactant, which inflates the theoretical yield and makes a good experiment look poor. The third is forgetting the container: a yield weighed with the dish still on the scale counts the dish as product. A yield between 80% and 90% is good for most school and undergraduate work; below 60%, something went wrong in the transfer or the washing, and above 100%, the product is wet or impure — dry it and weigh it again. One more trap is the theoretical yield itself: it is only as reliable as the balanced equation behind it, so an unbalanced equation or a wrong molar mass quietly inflates the maximum and makes every yield look low.

Frequently asked questions

What is theoretical yield?

The maximum product the balanced equation predicts, worked out from the limiting reactant — the reactant that runs out first. It assumes the reaction goes to completion with no losses.

Why is the yield never 100%?

Reactions rarely finish, some product stays in the filter paper or the flask, side reactions make other products, and purification always loses a little. 80–90% is a good yield for most school and lab reactions.

Can percent yield be over 100%?

Only if something is wrong — usually the product is wet, impure, or weighed with the container. A yield above 100% means the actual yield is not pure product; dry it and re-weigh.

How do I find the theoretical yield?

Balance the equation, find the limiting reactant, then use the mole ratio: moles of product = moles of limiting reactant × (product coefficient ÷ reactant coefficient), then convert moles to grams.

Does percent yield measure purity?

No — it measures how much product you recovered against the maximum possible. A 95% yield of impure product is worse than an 80% yield of pure product.

More tools

Tell us what you think

Loving this tool, or stuck on something? Tell us — it takes a minute.

We’ll only use your name and email to reply if needed. The tool and page are filled in for you.